This professional solar bollard light provides 4W of LED power using multiple, super bright, white Philips LEDs. It can distribute lighting 360 degrees. It's VERY easy to install almost anywhere and therefore ideal for illuminating footpaths, car parks, walkways, pedestrian and public areas, etc.
New for 2020. This commercial grade, solar bollard light fitting features a square shaped, clear polycarbonate lamp shade. It is made from dia-cast aluminum and the solar panel is built neatly into the top of the fitting. It is 100cm tall and produces an output of 500 lumens in full brightness mode sending light outwards and downwards all the way around it for several metres. It has a pre-installed lithium battery pack and control system inside the main body and a flange mount based allowing quick and easy Installation onto any solid surface. Colour of light output is white. Colour of product is black. Sold as a single unit. PLEASE NOTE: THIS IS A SPECIAL ORDER PRODUCT.
Perfect for commercial sites, communities, entrances areas to buildings, car parks, housing estates. footpaths and driveways, etc.
Professional, commercial grade bollard light fitting.
Heavy duty design and construction.
Automatic illumination at dusk and off at dawn.
16 super bright, high output, white coloured, Philips LEDs.
Each LED produces 35 lumens (130 lm/W).
IES file available upon request.
LED power is 4W (500 lumens total, at 100% brightness).
Clear polycarbonate lampshade.
UV treated to prevent yellowing.
IP68 weather rating.
Temperature range is -20 deg C (-4 deg F) to +80 deg C (176 deg F).
LED colour temperature choice is 3000k to 6500k.
Integrated passive infra-red motion sensor (PIR detector).
Main body section is made from marine grade, die cast aluminium.
Black powder coated finished to main body section.
Standard coloured finish is black.
Grey and other colours by special order.
The bollard has a main body that is approx. 15cm x 15cm (6" x 6") diameter.
The total height is approx. 100cm (39").
The square flange base is approx. 22cm x 22cm (8.5" x 8.5").
The flange section has four 10mm pre-drilled holes.
The clear lampshade top section is approx. 31cm x 31cm (12" x 12").
Other heights available by special order.
Certifications include CE, IEC, TUV,IESNA, RoHS LM-79 and LM-80.
Manufactured in an ISO9001 quality assured facility.
Supplied with a pre-installed lithium (LIFEPO4) battery.
The lithium battery is 6.4V / 6 A-Hr.
Typical lifespan is over 10 years and is replaceable.
Integrated MPPT charge controller.
Battery management system (BMS) feature.
Over load, over current, over temperature, over voltage, over charge and over discharge monitoring and protection.
High quality 6.3 Watt encapsulated monocrystalline solar panel.
The solar panel is set into the top section of the bollard fitting.
Grade A rated with tempered glass top.
The flange mount version is easily installed onto almost any horizontal, solid surface such as concrete, tarmac, wood, paving etc.
Installation time is usually less than 5 minutes per bollard.
The base section of the bollard has 4 pre-drilled holes for screw-down or bolt-down installation.
We recommend using stainless steel or galvanised steel expanding anchor bolts.
The root mount version will require a hole to be dig to accommodate the root section of the bollard body.
The solar panel must be installed in a location where it can receive full direct sunshine (when available) and set facing South at about a 45-60 degree angle (where adjustment options allow). The solar panel must not be installed in a shaded or part shaded location and never indoors. The standard specifications of the system (particularly the solar panel Wattage and battery capacity) may need to be adjusted. These components are determined by your geographic location, power consumption (LED Wattage) and the total amount of hours of illumination time required. Such changes to the standard specifications may increase or decrease the cost shown. Please contact us for more information or assistance. The illumination time is estimated and subject to various factors including (but not limited to) geographic location, seasons, temperature, weather conditions & location of product etc. The illumination time of most solar lights can reduce during winter months when the weather is poor and the days are shorter. During this time, insolation hours decrease accordingly. Shorter illumination time due to one or more of the above factors does not define the product as being ‘defective’ or ‘not as described’ or 'not fit for purpose'. All solar lights must be used in a dark location at night time otherwise they may not illuminate. Nearby strong lighting sources or ambient lighting may affect the operation of a solar light. This does not define the product as being 'defective' or 'not as described'. Please note, if you do not install or use this product for several months the battery may discharge naturally on its own. By allowing a battery to deep discharge it may cause irreversible damage as the battery may then lose the ability to recharge or hold a full charge. Although unlikely, we reserve the right to supply this product with any minor alterations or minor changes to the specifications (shown above by text description or by photographs) due to different supplies or product batches received, incorporating such product changes made by the manufacturer, without further notice. Descriptions, specifications and photographs are updated regularly but may not be current when minor changes to a product have only recently been made.
* View our Terms, Conditions and Polices (including our Returns Policy) for further information.
|Solar Lights Data|
|Lumen Output||500 lumens.|
|Equivalent Incandescent Wattage||Approx. 40W.|
|Approximate Illumination Time||Typically dusk to dawn.|
|Approximate Illumination Area||Up to approx. 5M diameter.|